Carriers spend a lot of time and money protecting operational and trip data collected and stored through various satellite, GPS, and cellular-based communications systems, but Ontario’s new speed-limiter legislation could open up your truck’s ECM to the prying eyes of Ministry of Transportation (MTO) or OPP inspectors each time it undergoes a speed limiter check.
Speed limiters are not, as they have been portrayed, microchips installed on engines to limit road speed. A speed limiter, as defined in the context of Ontario’s new legislation, is simply a single setting among hundreds of other customer-programmable settings within the electronic architecture of the vehicle’s engine control module (ECM).
But the setting cannot be made in isolation. Several variables must be defined within the ECM so that the number input as the road-speed upper limit (VSL) has context. These parameters include the pulses-per-revolution of the transmission output shaft, drive-tire rolling radius, and rear-axle gear ratio.
Bill 41 grants inspectors access your truck’s ECM with a cable link to either a laptop or a handheld device designed to verify compliance, such as a Pro-Link diagnostic tool. Inspectors will then scroll through the various settings displayed to ensure the VSL is set no higher than 105 km/h (65.2 mph), and the other parameters are in line with the VSL setting.
While each engine manufacturer has its own proprietary software and hardware for accessing and changing ECM settings, stored data such as the VSL, and the other settings mentioned above, can be read and extracted without extra proprietary tools or software — or passwords — provided the reader is compatible with the ECM.
“Law enforcement can interrogate the ECM, they can read and see what the road speed value is,” Cummins advised Today’s Trucking in an email response to questions. “ECM settings cannot be changed or altered with a read-only tool, but they can be read and extracted.”
MTO is currently examining Bill 41 and formulating an enforcement protocol that will allow its inspectors (and the OPP as well, presumably) to verify these setting at roadside, and will not comment how that’s to be done until the process is complete.
Former OPP Sgt. Cam Woolley demonstrates how speed limiter data is extracted from a truck engine’s ECM.
Unless some other method for verification is determined, the engine makers tell us MTO will require nonpassword-protected access to your ECM to verify those settings. Various aftermarket readers are available that will provide that access, but the act of hooking any computer or reader to an engine ECM is bound to raise some concerns. That’s why OEs and dealers are sensitive about who is connecting to an ECM and with what. We contacted Cummins, Caterpillar, Mack, Detroit Diesel, and Volvo to learn more about MTO’s proposed speed-limiter verification process.
So, is there any possibility of ECM damage, altered settings, or corrupted data arising from an ECM inspection event?
Detroit Diesel replied, “if the fleet owner has not password-protected (changed the default password) the parameters, then it is possible for someone, such as an inspector, to change parameter settings, including maximum road speed limit.“
Inspectors would need an OE-authorized tool to write settings to the ECM, so it’s unlikely that inspectors will be able to change settings while they are connected.
Cummins’ Lou Wensler acknowledged that damage to the ECM, or the corruption of data was possible if correct procedures are not followed.
Mack and Volvo were in general agreement with Cummins and Detroit Diesel on the above points (Caterpillar declined to provide input for this story), and each agreed there was little chance of a virus being transmitted from the reader to the ECM.
What’s Behind the Number?
In addition to simply verifying the VSL setting, inspectors are required by Bill 41 to check for evidence of tampering. An investigation of this sort might be prompted if a truck is caught “accelerating to, or maintaining a speed greater than 105 km/h on level ground.”
Various engine settings and recorded data could be visible to inspectors without passwords or access codes.
The VSL setting is not a number that can be viewed in isolation. It may read 105 (or the equivalent in computer-speak), but it is dependant on at least three other variables. If either of the entered driveshaft pulse-count, the rear-axle ratio number, or the tire revolutions per mile were inaccurate, the speed-limiter calibration would be meaningless, and this would be a significant concern to MTO.
By entering an incorrect tire size or gear ratio, the ECM can be tricked to read 105, when the truck may actually be able to travel much faster, Today’s Trucking learned.
“How would they verify the actual rear axle ratio in my truck?” asks Dale Holman of Truck Watch Services in Georgetown, Ont. “I’ve changed the gear sets in two of my trucks, and short of dismantling the rear axle, how will MTO find out?”
Holman says he redeployed those trucks from a run in northern Ontario to a route into the U.S. midwest, with decidedly different terrain and operating conditions. The taller gears improve fuel efficiency on flat ground. They’ll run faster, but his drivers do not run above 100 km/h, he says.
It is unlikely that Holman would be caught speeding, but if checked, he couldn’t guarantee all his numbers would actually add up to 105. Is that tampering?
When asked by Transport Canada if it was possible to determine specifics on if/when the speed limiter setting was tampered with, Dawn E. Friest of the Chicago-based EMA responded, “mismatched data might be an indicator of tampering, or might be the result of human error [when the values were input for example, or at the time of vehicle assembly]. There is no way to determine when tampering might have taken place.”
MTO could have quite a task on its hands dismantling drive axle carriers and counting gear teeth, or rolling trucks around the inspection station counting driveshaft revolutions over a distance and then doing a little math.
Then there are the optional driver incentive settings, such as Detroit Diesel’s PasSmart. Other OEs offer similar options under different brand names, but it’s an ECM setting allowing a driver a specified amount of speed and time over the VSL. It’s used to encourage better behavior by granting passing capability as a reward for good speed management. Those settings would have to be disabled if the spirit of Bill 41 were strictly adhered to. And it’s just one more setting the inspectors would have to go looking through your ECM to find.
One engine OE rep interviewed for this story confirmed that in addition to various engine settings, recorded data such as engine and road speed, idle intervals, hard-braking events, key-on and key-off times, etc., would also be visible without passwords or access codes.
“That data is not usually password protected, or if it is, it’s just behind the default password,” he said. “Most customers don’t bother resetting a new password.”
Even if they did, MTO could well demand it be cleared to allow VSL verification.